Ensurepass.com : Ensure you pass the IT Exams
2018 May VMware Official New Released 2V0-651
100% Free Download! 100% Pass Guaranteed!

VMware Certified Professional 6 – Network Virtualization Beta

Question No: 41

Which two are valid statements regarding third-party services and NSX? (Choose two.)

  1. Third party services are automatically registered with NSX Manager.

  2. Third party services can either be automatically or manually registered with NSX Manager.

  3. Third party services require the deployment of a virtual appliance.

  4. Third party services may or may not utilize a service virtual appliance.

Answer: B,D

Question No: 42

Which two options are pieces of information required to perform an NSX backup? (Choose two.)

  1. Transfer protocol

  2. Default Port

  3. Number of backups retained

  4. Filename prefix

Answer: A,D

Question No: 43

Which three network policy settings can only be configured on a vSphere 5.5 Distributed Switch? (Choose three.)

  1. Access Control Lists (ACLs)

  2. Network I/O Control

  3. LACP v2

  4. NetFlow

  5. DSCP Marking

Answer: A,C,E

Question No: 44

High Availability (HA) was not initially configured when an administrator deployed an NSX Edge Service Gateway. What should the administrator do to configure the NSX Edge with HA?

  1. Select the NSX Edge instance from the NSX Edges view in Networking amp; Security. Go to Managegt; Settingsgt; Configuration and add a NSX Edge appliance.

  2. Delete the NSX Edge instance and redeploy it with HA. The existing NSX Edge configuration data will be lost.

  3. Delete the NSX Edge instance and redeploy it with HA. The configuration data is retained by NSX Manager and pushed to the new NSX Edge instance.

  4. Select the NSX Edge appliance from the Virtual Machines and Templates view. Go to Actionsgt; All vCenter Actionsgt; Enable HA to configure High Availability.

Answer: A

Question No: 45

– Exhibit –

Ensurepass 2018 PDF and VCE

– Exhibit –

An administrator is deploying a distributed router and is adding an interface for a logical switch, as shown in the following exhibit.

The administrator clicks on the Change link to specify the network to connect to. Selecting the distributed portgroup, the administrator finds that no portgroups are listed. The administrator verifies the desired portgroup exists in vCenter Server.

What condition would result in this behavior?

  1. The MTU size is set to 1500.

  2. A subnet has not been configured.

  3. The interface name has an invalid character.

  4. The interface type is incorrect.

Answer: D

Question No: 46

What is the function of NSX Data Security?

  1. Prevents sensitive data in your virtualized environment from being copied

  2. Prevents sensitive data in your virtualized environment from being modified

  3. Identifies sensitive data in your virtualized environment based upon regulation security policies

  4. Identifies sensitive data in your virtualized environment based upon regulation violation reports

Answer: D

Question No: 47

Which two options are use cases of Layer 2 bridging in NSX for vSphere? (Choose two.)

  1. Extend the network security to physical devices in the physical network by use of the Distributed Firewall.

  2. Extend physical services to Virtual Machines in virtual network.

  3. Allow clustering of multiple NSX Managers in a single vCenter Server instance.

  4. Allow physical devices in the physical network to use the NSX Edge Gateway as a default router.

Answer: B,D

Question No: 48

– Exhibit –

Ensurepass 2018 PDF and VCE

– Exhibit –

An NSX administrator has deployed the network shown in the Exhibit.

Based on the exhibit, which statement describes a valid method for redirecting traffic around the fault?

  1. Building this topology using a layer 2 switched fabric with connectivity between the leafs would allow traffic to be redirected around the fault to another leaf.

  2. Building this topology using a layer 3 routed fabric with connectivity between the leafs would allow traffic to be redirected around the fault to another leaf.

  3. Building this topology using a layer 2 switched fabric with spanning tree will provide the quickest path around the fault to another spine when connectivity is lost.

  4. Building this topology using a layer 3 routed fabric will provide the quickest path around the fault to another spine when connectivity is lost.

Answer: D

Question No: 49

Where must you go to manually register a third-party service with VMware NSX?

  1. vSphere Web Client -gt; Networking amp; Security -gt; Installation -gt; Service Deployments tab

  2. vSphere Web Client -gt; Networking amp; Security -gt; Service Composer -gt; Service Deployments tab

  3. vSphere Web Client -gt; Networking amp; Security -gt; Service Definitions

  4. vSphere Web Client -gt; Networking amp; Security -gt; Distributed Firewall -gt; Service Definitions

Answer: C

Question No: 50

How does NSX simplify the underlying physical network?

  1. All configuration and state information is available via the REST APIs to automate the configuration of the physical network.

  2. All configuration and state information are readily accessible, as is the mapping between virtual network topologies and the physical network.

  3. All configuration and state information is stored in the local NSX BPDU database, eliminating the need for Spanning Tree Protocol (STP) on the physical network.

  4. All configuration and state information is cached by the NSX controllers, reducing the number of MAC/ARP table entries on the physical network.

Answer: B

100% Ensurepass Free Download!
Download Free Demo:2V0-651 Demo PDF
100% Ensurepass Free Guaranteed!
2V0-651 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No