Ensurepass

Troubleshooting Cisco Data Center Unified Fabric (DCUFT)

 

QUESTION 61

Refer to the exhibit. During a VSAN outage, youcome across this configuration. Please select two possible causes. (Choose two.)

 

clip_image002

 

A.

no common VSANs on both switches

B.

no common trunks

C.

no common VSAN members in the same trunk

D.

VSANs in trunk are the same, but the trunk is not up

 

Correct Answer: AC

 

 

QUESTION 62

Refer to the exhibit. Which two options are causes of the error when setting up VM-FEX on the Cisco UCSB-Series Blades? (Choose two.)

 

clip_image004

 

A.

Dynamic vNICs are not supported on the version the admin is running.

B.

The network adapter in the blade does not support dynamic vNICs.

C.

Too many dynamic vNICs are configured.

D.

Dynamic vNICs are not required for VM-FEX.

E.

The dynamic vNIC connection policy was never applied to the service profile.

 

Correct Answer: BC

 

 

QUESTION 63

Why do the lists not contain the same switches, after you issue the commands show cfs peers name and show cfs merge status?

 

A.

The merge cannot occur until the VSAN IDs are synched.

B.

The Cisco Fabric Services fabric has a physical port fault that should be investigated.

C.

The fabric is partitioned into multiple Cisco Fabric Services fabrics.

D.

Cisco Fabric Services need to b
e restarted to see the new switches.

E.

A Cisco Fabric Services database lock has prevented the merge.

 

Correct Answer: C

 

 

QUESTION 64

You apply a new CoPP profile to a Cisco Nexus 7000 Series, and it stops responding to ping requests. Which option should you check?

 

A.

server SO

B.

SVI that is associated with the server subnet

C.

CoPP counters

D.

< /td>

ACL that is associated with the CoPP profile applied

 

Correct Answer: D

 

 

QUESTION 65

Which statement is true regarding Cisco FabricPath?

 

A.

It is necessary to first install the Cisco FabricPath feature set in the default VDC.

B.

Cisco FabricPath is only available on Cisco Nexus 7010 Switches with the Supervisor 2 engine.

C.

Cisco FabricPath cannot be disabled explicitly for a specific VDC.

D.

If the Cisco FabricPath feature is not installed, the fabricpath ke
yword will be available in the feature-set command.

 

Correct Answer: A

 

 

QUESTION 66

OTV is configured-testpings confirm that it is working butother tests do not seem to perform well. What is the problem?

 

A.

VLANs are not properly extended.

B.

The multicast groups are not defined properly.

C.

The transport network is not configured to process the overhead that is introduced by OTV.

D.

The overlay may not be enabled.

 

Correct Answer: C

 

 

QUESTION 67

Refer to the exhibit. What are three valid commands to troubleshoot why the port is disabled? (Choose three.)

 

clip_image006

 

A.

show san-port-channel compatibility-parameters

B.

show port info internal interface fc <slot/port>

C.

show san-port-channel internal info

D.

show port internal event-history interface fc <slot/port>

E.

show interface san-port-channel detail all

F.

show san-port-channel internal event-history all

G.

show internal interface event-history all

 

Correct Answer: ADF

 

 

QUESTION 68

Which command would you use to check the status of your configuration synchronization peer?

 

A.

N5K2# show switch-profile peer

B.

N5K2# show config-sync peer

C.

N5K2# show synch peer

D.

N5K2# show peer status

E.

N5K2# show switch peer

 

Correct Answer: A

 

 

QUESTION 69

A customer is troubleshooting FCoE in its network. They have discovered that vFC is currently down and there is no active STP port state on the bound Ethernet interface. What should the STP port state be to correct this issue?

 

A.

The bound interface should be in an STP forwarding state for the native VLAN only.

B.

The bound interface should be in an STP learning state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

C.

The bound interface should be in an STP forwarding state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

D.

The bound interface should be in an STP blocking state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

 

Correct Answer: C

 

QUESTION 70

Which three statements are true about the show cfs merge status name command? (Choose three.)

 

A.

In a successful merge, all switches in the fabric are shown separately.

B.

The command shows the complete Cisco Fabric Services region database.

C.

The command shows the merge status in all valid VSANs on the switch.

D.

The merge master is selected based on the highest sWWN in the fabric.

E.

The merge master is selected based on the lowest sWWN in the fabric.

F.

In a successful merge, all switches are shown in a local fabric.

 

Correct Answer: CEF

 

Free VCE & PDF File for Cisco 642-980 Practice Test

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …